Russian inlets
Moderator: Mike Everman
-
- Posts: 5007
- Joined: Fri Oct 31, 2003 7:25 am
- Antipspambot question: 0
- Location: santa barbara, CA
- Contact:
-
- Posts: 474
- Joined: Mon Jul 30, 2007 2:43 am
- Antipspambot question: 0
- Location: British living in Chile
Heres a fun vid ,
The first thing that calls attention to me , is the state of my backyard,
must make a mental note to have a word with my wife about that ,
Noteworthy might be the fact that I estimate 80% of the thrust is coming from the inlet , but that’s not surprising considering the length and diameter of the tailpipe.
I will do something similar once I put the straight inlet back on , to compare ,
You know how one idea leads to another, washing lines and all,
I remembered that my mother had a washing line that was triangular and would spin around a central post ,
That little neuron caused an acid flashback,
Many years ago I had An electric rig called Round the pole ,
It involved small electric foam planes flying around a central post , the current ran through 2 small ball races, and thence to the airplane via 2 wires,
From what I remember the “craft” doesn’t have to be anything at all elaborate , centrifugal force plays a huge role here in getting even horrendous airframes into the air ,
Now taking things a step further ;
A 2” diameter steel pipe concreted into the ground about 5ft tall, with a rotary union for the gas , and maybe 30 ft lines, Might be a (frightening but fun) way of getting some engine/airframe testing done before the shit or bust ramp launch routine,
One could even put r/c gear in the craft for elevator control ,
Hmm I can feel a winter project coming on ,
And by the way if anyone here has a mother who has a triangular washing line , I accept no responsibility whatsoever for any potentially lethal fun you might have,
BTW the places that sell pneumatic valves and cylinders , also keep rotary unions,
The first thing that calls attention to me , is the state of my backyard,
must make a mental note to have a word with my wife about that ,
Noteworthy might be the fact that I estimate 80% of the thrust is coming from the inlet , but that’s not surprising considering the length and diameter of the tailpipe.
I will do something similar once I put the straight inlet back on , to compare ,
You know how one idea leads to another, washing lines and all,
I remembered that my mother had a washing line that was triangular and would spin around a central post ,
That little neuron caused an acid flashback,
Many years ago I had An electric rig called Round the pole ,
It involved small electric foam planes flying around a central post , the current ran through 2 small ball races, and thence to the airplane via 2 wires,
From what I remember the “craft” doesn’t have to be anything at all elaborate , centrifugal force plays a huge role here in getting even horrendous airframes into the air ,
Now taking things a step further ;
A 2” diameter steel pipe concreted into the ground about 5ft tall, with a rotary union for the gas , and maybe 30 ft lines, Might be a (frightening but fun) way of getting some engine/airframe testing done before the shit or bust ramp launch routine,
One could even put r/c gear in the craft for elevator control ,
Hmm I can feel a winter project coming on ,
And by the way if anyone here has a mother who has a triangular washing line , I accept no responsibility whatsoever for any potentially lethal fun you might have,
BTW the places that sell pneumatic valves and cylinders , also keep rotary unions,
- Attachments
-
- wash line thrust.wmv
- (1.99 MiB) Downloaded 1117 times
-
- Posts: 1396
- Joined: Thu Oct 06, 2005 1:34 am
- Antipspambot question: 0
- Location: DEMING NM 88030
-
- Posts: 1396
- Joined: Thu Oct 06, 2005 1:34 am
- Antipspambot question: 0
- Location: DEMING NM 88030
Pat Pend Clothes Line Be Gone
Here You Go Grim! Your Next Step!
Note: No Pantent Required.
Note: No Pantent Required.
- Attachments
-
- Woopie Clothes Line be Gone.jpg (25.31 KiB) Viewed 6432 times
WHAT TO FRAP, IT WORKED![url=callto://james.a.berquist][/url]
-
- Posts: 4140
- Joined: Sun Oct 05, 2003 1:17 am
- Antipspambot question: 0
- Location: Mingo, Iowa USA
- Contact:
-
- Posts: 474
- Joined: Mon Jul 30, 2007 2:43 am
- Antipspambot question: 0
- Location: British living in Chile
Lock stock and two smoking barrels
This should really make the washing line whiz round, Less moped, more ricer 4 pot at idle,
I had to keep the revs down , “Her indoors” was home,
Jim the drawing is brilliant,
The film is one of my favorites , they are east enders , and yes they really do speak like that, you tube it , there’s some good clips ,
I come from the other side of the river , similar accent but slightly toned down,
“ I told you to blow the bloody doors off ”
I had to keep the revs down , “Her indoors” was home,
Jim the drawing is brilliant,
The film is one of my favorites , they are east enders , and yes they really do speak like that, you tube it , there’s some good clips ,
I come from the other side of the river , similar accent but slightly toned down,
“ I told you to blow the bloody doors off ”
- Attachments
-
- Lock stock and two smoking.wmv
- (1.94 MiB) Downloaded 1034 times
-
- Posts: 474
- Joined: Mon Jul 30, 2007 2:43 am
- Antipspambot question: 0
- Location: British living in Chile
I believe that some of the “wind” musical instruments do indeed have something in common with pulsejets with their resonant nature,
I always think of them penny whistles, simply covering or uncovering one or more small holes, in essentially a straight tube will produce a totally different frequency , could be that’s why one should take care to keep all the welds airtight,
Some small holes in strategic places with little stoppers, Could be a way of tuning an engine maybe ha,
I always think of them penny whistles, simply covering or uncovering one or more small holes, in essentially a straight tube will produce a totally different frequency , could be that’s why one should take care to keep all the welds airtight,
Some small holes in strategic places with little stoppers, Could be a way of tuning an engine maybe ha,
-
- Posts: 474
- Joined: Mon Jul 30, 2007 2:43 am
- Antipspambot question: 0
- Location: British living in Chile
I apologize in advance if I am boring you , heres another vid , and a couple of photos
The big difference is that the tailpipe is only 23 “ long now , making an overall length of 27” so I guess it is a real pulsejet that can jam jar , its running at about ¾ throttle here ,
I surprised myself , prior to shutdown I tried to flame it out and discovered there is a bunch more throttle once really hot ,
I have also modified the shape of the inlet , the cone is shorter now ,
The big difference is that the tailpipe is only 23 “ long now , making an overall length of 27” so I guess it is a real pulsejet that can jam jar , its running at about ¾ throttle here ,
I surprised myself , prior to shutdown I tried to flame it out and discovered there is a bunch more throttle once really hot ,
I have also modified the shape of the inlet , the cone is shorter now ,
- Attachments
-
- run up.wmv
- (1.87 MiB) Downloaded 914 times
-
- IMG_0692.JPG (30.31 KiB) Viewed 6253 times
-
- Posts: 4140
- Joined: Sun Oct 05, 2003 1:17 am
- Antipspambot question: 0
- Location: Mingo, Iowa USA
- Contact: